Updated November 2026

To repair drywall after wallpaper removal, you will strip off the leftover adhesive and loose paper, fill the gouges and torn paper with joint compound, sand the surface flat, and prime it before painting. Done right, the wall looks like it was never papered. The work is mostly patience: each coat needs to dry fully before the next one goes on.

Assess the Damage Before You Start

Wallpaper pulls up the outer paper layer of drywall in most cases, leaving the gypsum core exposed and soft. Run your hand across the wall in good light. If you see fuzzy patches, gouges, or areas where the paper peels when you press it, you will need to repair the surface, not just paint over it. Small spots of paper loss can be handled with joint compound, while larger areas that crumble may need a fuller patch like those covered in How to Repair a Huge Hole in Drywall: A Step-by-Step Guide.

Shopping for one? See our guide: 6 Best 3M Drywall Repair Kit Options for Home Repairs (2026).

Remove the Wallpaper and Adhesive Residue

Start by scoring the paper with a scoring tool or a utility knife so the solution can soak in. Mist the wall with warm water mixed with a few drops of fabric softener or a commercial wallpaper stripper, wait 10 to 15 minutes, and scrape with a broad putty knife held at a low angle. Work in small sections and keep the blade flat so you do not dig into the gypsum. Repeat the soak until the paper comes away cleanly, then wash the wall with warm water and a sponge to remove the glue.

Tools you will need

  1. Scoring tool or utility knife
  2. Wallpaper stripper or a spray bottle and fabric softener
  3. Wide putty knife (6 inch or 8 inch)
  4. Sponges and a bucket of warm water
  5. All-purpose joint compound and a 6 inch and 10 inch taping knife
  6. Fine sanding sponge or 120-grit sanding screen
  7. Drywall primer

Fill, Feather, and Sand the Surface

Once the wall is dry, check it again for soft spots. Press firmly with the blade of a putty knife and remove any paper that lifts. Apply a thin coat of all-purpose joint compound over gouges, using the 6 inch knife to press it into the low spots. Let it dry completely, which usually takes several hours depending on humidity and coat thickness. Then apply a second coat with the 10 inch knife, extending it 2 to 3 inches past the first layer so the edges blend into the wall. Sand lightly with a fine sponge once the compound is hard. Avoid aggressive sanding, which can expose more paper and leave swirl marks.

Prime and Inspect Before Painting

Joint compound and bare drywall absorb paint at different rates, so the patches will show through a topcoat unless you prime first. Use a drywall primer across the entire wall, not only the repaired spots. After the primer dries, shine a work light across the surface at a low angle. Any ridges, pinholes, or dull areas will appear clearly. Mark them, sand lightly, and add a thin skim coat if needed before the final primer coat.

Common Mistakes

  • Skipping the wash step. Leftover adhesive will make joint compound and paint bond poorly and can cause bubbles.
  • Applying compound too thick. Thick coats crack and take days to cure, so build up in several thin layers.
  • Sanding through the paper. Over-sanding creates fuzzy spots that show through paint.
  • Painting without primer. Patched areas will look flat and shiny compared to the surrounding wall.

A flexible taping knife set makes it easier to feather compound at the edges of patches, which is where most visible lines come from. A sanding sponge works better than sandpaper on wall surfaces because it conforms to slight curves and avoids gouging. Drywall primer is essential for sealing repaired areas so the paint finish looks uniform. View on Amazon View on Amazon View on Amazon

FAQ

Can I repair drywall after wallpaper removal without sanding?

Light sanding is almost always needed to smooth dried joint compound. Skipping it usually leaves ridges that show under paint, so a fine sponge pass is worth the few minutes it takes.

How many coats of joint compound do I need?

Most repairs take two to three thin coats. Each coat should dry completely before the next, and the final coat should extend beyond the damage to blend in.

Do I need to remove all the wallpaper paper backing?

Yes, remove any loose or peeling paper, but leave firmly bonded paper alone if it is sound. Pulling off intact drywall paper can strip the gypsum and make the wall harder to fix.

Conclusion

Removing the wallpaper and its adhesive takes the most time, but the repair itself comes down to thin coats, careful sanding, and a full coat of primer. Take each step slowly and inspect the wall in raking light before painting. A smooth result is well within reach for a patient DIYer.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.