Updated November 2026
Underfelt for laminate flooring is the thin layer that sits between your subfloor and the planks. It cushions footsteps, cuts down on noise, smooths small imperfections, and in many cases provides a moisture barrier. Get the right type and lay it correctly, and your laminate will feel better underfoot and hold up longer.
Choose the Right Type of Underfelt
Most underfelt falls into three groups: foam, cork, and felt-based or rubber-blend products. Foam is the most common and works well over flat concrete or plywood. Cork absorbs sound and recovers well after being compressed, which makes it a good match for upper floors. Felt-based and rubber-blend options are denser and suit uneven subfloors where extra cushion helps.
Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).
Check the packaging for a vapor barrier rating if you are installing over concrete. A plastic or foil-faced layer blocks moisture rising from the slab. Many laminate warranties require one on concrete, so confirm the manufacturer’s requirements before you buy.
Prepare the Subfloor First
Underfelt cannot fix a bad subfloor. Before you roll anything out, sweep and vacuum thoroughly, then check for high spots and gaps. Use a straightedge that is at least 6 feet long. Manufacturers generally call for a flatness tolerance of about 3/16 inch over a 10-foot span. Grind down high spots and fill low ones with a leveling compound.
Check moisture on concrete slabs with a moisture meter or the plastic sheet test: tape a 2-foot square of plastic to the slab, seal the edges, and wait 48 hours. Condensation under the plastic means you need a moisture mitigation system before proceeding. The guide Subfloor Preparation and Flooring Underlayment Explained covers this in more detail.
How to Lay Underfelt for Laminate Flooring
- Measure the room and add 10 percent for cuts and waste.
- Roll out the underfelt perpendicular to the direction you plan to lay the planks, so the seams do not line up with the plank joints.
- Overlap each strip by 4 to 6 inches and seal the seams with the tape the manufacturer recommends. Do not leave gaps.
- Run the underfelt 1 to 2 inches up the walls, then trim it flush after the planks are down.
- Keep the underfelt flat by weighting the edges while you work. Avoid stretching it.
- Start laying the laminate planks on top, leaving a 1/4 to 3/8 inch expansion gap at the walls.
If you are new to the full installation, How to Install Laminate Flooring: A Step-by-Step Guide for Beginners walks through the planks, locking and trimming in sequence.
Match the Underfelt to Your Subfloor and Room
Thickness matters, but more is not always better. Very thick underfelt can make planks feel bouncy and can weaken the locking joints over time. For most subfloors, a moderate thickness with a built-in vapor barrier is the practical choice. Over an upper floor, look for a product rated for sound reduction. Over a basement slab, prioritize the vapor barrier. A related read: White Oak Flooring Laminate: How to Choose and Install It (Step-by-Step).
| Situation | Underfelt to look for |
|---|---|
| Concrete slab, ground floor | Foam or felt with attached vapor barrier |
| Plywood subfloor, upper floor | Cork or foam with sound-reduction rating |
| Uneven subfloor | Denser felt or rubber blend |
| Radiant heat | Thin foam rated for radiant heat use |
Common Mistakes
- Skipping the vapor barrier on concrete, which can lead to cupping and warranty problems.
- Letting seams line up with plank joints, which can cause squeaks and weak spots.
- Choosing underfelt that is too thick for floating laminate, which makes the floor feel unstable.
- Leaving gaps between sheets, which allow moisture and debris underneath.
- Installing over an unprepared subfloor and expecting the underfelt to hide bumps.
Recommended Gear
- Underlayment tape: Sealing seams keeps the vapor barrier continuous. View on Amazon
- Straightedge: A long, rigid straightedge helps you spot high and low spots before laying. View on Amazon
- Moisture meter: A concrete moisture meter gives you a reading before you commit to a vapor barrier choice. View on Amazon
FAQ
Do I always need underfelt under laminate flooring?
Most laminate manufacturers require underfelt or an attached underlayment for warranty coverage. It also improves comfort and sound. Check your product’s installation instructions before skipping it.
Can I use one underfelt for both concrete and wood subfloors?
Some products work over both, but if you are on concrete you need a vapor barrier. Confirm the product is rated for your specific subfloor type.
Should underfelt be taped or can it simply overlap?
Seams should be taped to keep the barrier continuous and prevent shifting. Overlap alone is not enough on most products. Follow the manufacturer’s tape recommendation.
Conclusion
Underfelt for laminate flooring is a small layer with a big effect on comfort, sound and moisture protection. Match the type to your subfloor, prepare the surface properly, and tape the seams carefully. For moisture or structural concerns, consult a flooring professional before you begin.

