Updated November 2026

A good cutter for laminate flooring lets you make straight, clean cuts through planks in a few seconds, without the dust and noise of a power saw. This guide explains which cutter fits your project, how to use it on boards that need trimming, and where DIY installers usually go wrong. Our first cut on a hallway run taught us most of this the hard way.

Choose the Right Cutter for Your Job

Most installers use one of two tools. A laminate cutter (sometimes called a tile-style or snap cutter) uses a scoring wheel and a long straight blade to score the surface, then snaps the plank along the score line. A jigsaw or fine-tooth handsaw handles cuts the snap cutter can’t make, such as door casings, pipes and irregular curves.

Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).

For long, straight rips across the width of a plank, a laminate cutter is faster and leaves a cleaner edge. Use a jigsaw with a fine-tooth blade for notches and curves, and plan to finish those edges with a file or sanding block.

Step-by-Step: Making a Straight Cut

  1. Measure the gap at the point of cut. Mark the face of the plank with a pencil, then add a line on the tongue side if you’re trimming a long edge.
  2. Place the plank on a flat, firm surface with the decorative face up. Support both ends so the plank doesn’t flex.
  3. Align the cutter’s guide edge with your mark. Hold the plank down firmly with one hand.
  4. Draw the scoring wheel or blade along the line in one smooth pass. Repeat two or three times if your tool calls for it, applying steady downward pressure.
  5. Lift the plank and snap it along the score by bending it sharply away from the scored side. Support the waste piece so it doesn’t tear the face.
  6. Test-fit the cut piece before moving on. Sand the edge lightly if it’s rough.

Tips for Cutting Without Chips

Laminate surfaces chip when the blade or wheel exits the board, so the way you finish each pass matters as much as the cut itself. Cut with the decorative face up for a jigsaw, and with the face down only if your tool specifically requires it.

Cutting Around Obstacles

Doorways and pipes need notches. Make the notch a few millimeters larger than the obstacle, then fill the extra gap with a flexible trim or quarter-round so the edge stays hidden. Cut the notch from the back side of the plank when you can, since the face is less likely to chip.

Common Mistakes to Avoid

  • Scoring once and expecting a clean snap. Most cuts need two or three passes to break cleanly.
  • Cutting on an unsupported plank. The board flexes and the score line cracks unevenly.
  • Using a dull blade or wheel. Replace it when it starts skipping on the surface.
  • Forgetting the expansion gap. Leave the gap at the wall after cutting, or the floor can buckle.
  • Measuring from a plank that has already been cut. Measure each piece individually to reduce waste.
  • Laminate flooring cutter: A snap-style cutter with a long guide rail gives straight cuts across full-width planks. View on Amazon
  • Fine-tooth jigsaw blades: Blades designed for laminate or laminate-compatible materials reduce chipping on notches and curves. View on Amazon
  • Sanding block: A small block smooths rough edges after a notch or saw cut so the fit stays tight. View on Amazon

If you’re planning a full installation, the broader process is covered in How to Install Laminate Flooring: A Step-by-Step Guide for Beginners, and our overview of Flooring Installation Tools: Cutters, Spacers, Tapping Blocks and More compares the other tools you’ll need.

FAQ

Can I cut laminate flooring with a utility knife?

You can score the surface with a utility knife, but you still need to snap the board, and the results are less consistent than a dedicated cutter. A cutter or jigsaw gives a cleaner edge for most jobs.

Do I need a power saw for laminate flooring?

Not for straight cuts. A snap cutter handles most lengths, and a jigsaw covers notches and curves. A power saw is useful only for very large jobs with many cuts.

Why does my laminate chip when I cut it?

Chipping usually comes from cutting with the wrong blade, skipping the support under the board, or pushing too hard on the exit pass. Slow down, support both ends, and use a fresh blade.

Conclusion

For most laminate projects, a snap-style cutter handles straight cuts and a jigsaw covers the rest. Support each plank, make a few light passes, and finish the edges by hand. Check the manufacturer’s instructions for your specific flooring, since some products call for particular tools or cutting methods.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.