Updated November 2026
Yard drain tile installation means burying perforated pipe in a trench so that groundwater and surface runoff move away from a soggy lawn, a foundation or a low corner of the yard. In this guide you will learn how to confirm the problem, plan a route with a proper outlet, dig and grade the trench, and lay the pipe so it keeps working for years. The job is physical but straightforward if you take your time with slope.
Confirm the Problem and Plan the Route
Before you dig, watch the yard during and after a heavy rain. Note where water pools, how long it lingers and whether it runs toward a low spot or a neighbor’s property. Plan the route so the drain runs downhill to a legal outlet, such as a storm sewer connection where allowed, a dry well, or a daylight outlet at a lower grade. Check with your city or county about permits and utility locations before you dig, and call 811 in the US to have buried lines marked.
Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).
If the water is coming from the house side, read the guide to drain tile system installation for wet basements first, because the layout and outlet rules differ.
Gather Tools and Materials
- Flexible perforated drain pipe, usually 4-inch corrugated, with a sock or filter fabric
- Clean drainage gravel or crushed stone, roughly 3/4-inch
- Landscape fabric to wrap the gravel bed
- Spade, flat shovel, mattock and a pick for hard soil
- Line level, string line and stakes
- Four-foot level and a tape measure
- Pipe cutter or sharp utility knife, and fittings
Dig and Grade the Trench
Dig the trench 12 to 18 inches deep at the upstream end and deepen it gradually toward the outlet. Keep the bottom as smooth as you can, removing rocks and roots, and check the fall with your string line and line level. A common target is about 1/8 inch of fall per foot of run, which gives the water a steady push without scouring the gravel. Keep the trench width around 8 to 12 inches so you have room to work the gravel under and around the pipe.
Set the Gravel Bed
Spread 2 to 3 inches of gravel in the bottom and tamp it lightly. Lay landscape fabric along the trench before adding gravel if the soil is fine and silty, since fine particles can clog the pipe. Your gravel base should follow the same slope as the trench.
Lay the Pipe and Connect the Outlet
Lay the perforated pipe with the holes facing down or to the sides, depending on the manufacturer’s directions, and keep joints tight. Cover the pipe with at least 6 inches of gravel, then fold the fabric over the top and backfill with soil. At the outlet, use a solid (non-perforated) pipe for the last several feet so the discharge does not wash out the soil near the end. Protect the outlet with a screen or grate, and keep it clear of leaves and debris.
Common Mistakes
- Using too little fall, which lets water sit and silt settle in the line.
- Skipping fabric in silty soil, so fines clog the gravel and pipe.
- Ending the drain in a low spot that cannot carry the water away.
- Backfilling with clay directly over the gravel, which can slow flow.
- Forgetting to check local rules before tying into a sewer or storm connection.
Recommended Gear
- A flexible corrugated perforated drain pipe with a filter sock helps keep fines out of the line and makes cutting and joining simpler. View on Amazon
- Landscape filter fabric keeps soil from migrating into the gravel bed. View on Amazon
- A four-foot level with a built-in bubble gives you a reliable check on slope along the trench. View on Amazon
FAQ
How deep should yard drain tile be buried?
Most lawn drains are buried about 12 to 18 inches deep, enough to stay below the root zone and clear of normal surface traffic. The exact depth depends on frost line, existing utilities and where the outlet sits. Check local code before you dig.
Can I connect yard drain tile to the storm sewer?
Some areas allow it and others prohibit it, so confirm with your municipality first. Connections often require a permit and must meet specific standards. When in doubt, ask a licensed professional or the local public works office.
How long does a yard drain last?
A properly graded and filtered system can last many years, but it needs clear outlets and occasional cleaning. Keep leaves and silt out of the outlet and inspect it after heavy storms. If you’re unsure about the design, consult a qualified drainage contractor.
Conclusion
With the trench graded, the gravel and fabric in place, and a clear outlet, your yard drain tile installation will move water away from the problem area. Test it with a garden hose before backfilling completely, and watch how it performs after the next heavy rain. Adjust the outlet or add a second line if a low spot still holds water.

