Updated November 2026
Hardwood flooring installation on concrete is very doable for a DIY renovator, but the concrete does most of the deciding. Before you buy a single board, you need to confirm the slab is dry, flat, and sealed against moisture. Get those three things right and the floor will sit tight, stay quiet, and last for decades.
Test the Slab for Moisture First
Concrete releases water vapor for months after it is poured, and wood swells when it absorbs that moisture. Tape a 2-foot square of clear plastic sheeting to the slab, seal all four edges, and leave it for 48 hours. If you see condensation under the plastic or the concrete darkens, the slab is too wet to install over without a moisture barrier. Many flooring manufacturers publish a maximum moisture reading, often expressed as a calcium chloride test result or a relative humidity percentage in the slab. Check the specific limits in your flooring’s installation instructions and consider a professional moisture test if your results are borderline.
Prepare and Level the Subfloor
Hardwood needs a flat surface, and most manufacturers call for no more than about 3/16 inch of variation over a 10-foot span. Use a straightedge to find high spots and grind them down. Fill low spots with a patching compound made for concrete, then let it cure fully. Sweep, vacuum, and remove old adhesive, paint drips, and any sealers that could block a glue bond.
Steps for Prep
- Clean the slab thoroughly and remove all debris and old adhesive.
- Mark high spots with a pencil and grind them flush.
- Fill low spots and cracks with leveling compound, then allow the full cure time listed on the bag.
- Recheck flatness with a straightedge in several directions.
- Vacuum one final time before laying any materials.
Add a Moisture Barrier and Underlayment
Lay a 6-mil polyethylene vapor barrier across the slab, overlapping seams by 6 inches and taping them. Over that, install a foam or cork underlayment if your flooring type calls for one. Check whether your product is designed to float or be glued down, because the barrier and underlayment choices differ. A floating floor needs underlayment that cushions the planks and blocks sound. A glue-down floor needs a compatible adhesive and, usually, no foam underlayment at all.
Choose Between Floating and Glue-Down Methods
A floating floor locks together and rests on the underlayment without being attached to the slab. This method is forgiving for a first-timer and leaves room for seasonal movement. Glue-down installation bonds the boards directly to the concrete with a urethane or wood-flooring adhesive. It feels more solid underfoot and suits engineered boards well, but the work is messier and harder to undo. Use the layout that matches your product’s instructions, and follow the adhesive manufacturer’s open time closely.
Common Mistakes
- Skipping the moisture test and assuming a new-looking slab is dry.
- Leaving a gap at the perimeter. Most floors need an expansion gap of roughly 1/2 inch at walls, covered by trim.
- Running boards in a single direction across long rooms without checking the layout pattern first.
- Installing over an unsealed or dusty slab, which weakens adhesive bonds.
- Ignoring the flooring manufacturer’s temperature and humidity requirements during acclimation.
Recommended Gear
- Stanley FatMax 78-inch Straightedge: a long, rigid straightedge helps you spot high and low spots before they cause problems. View on Amazon
- Roberts Multi-Purpose Underlayment: a floating-floor underlayment that many installers pair with engineered boards. View on Amazon
- Roberts Wood Floor Adhesive: a urethane-style adhesive designed for glue-down wood installations. View on Amazon
If you want a deeper look at tools, see 6 Best Hardwood Flooring Installation Tools for DIY Renovators (2026). For layout ideas, read Hardwood Flooring Installation Patterns: 5 Layouts and How to Pick One.
FAQ
Can I install hardwood directly on concrete?
Yes, but only if the slab is dry, flat, and protected by a vapor barrier. Solid hardwood is usually not recommended over concrete, so engineered boards are the safer choice.
Do I need underlayment over concrete?
Often yes. A moisture barrier is almost always needed, and a cushion layer is needed for most floating floors. Confirm the requirements in your product’s installation guide.
Should I hire a professional for this job?
If your moisture test fails or the slab has major cracks or uneven areas, consult a flooring professional or a structural contractor before proceeding.
Conclusion
Successful hardwood flooring installation on concrete comes down to three checks: moisture, flatness, and a proper barrier. Test the slab, prepare it carefully, and choose the floating or glue-down method your product supports. Take your time on prep, and the finished floor will reward you.

