Updated November 2026

Installation of laminate flooring on concrete is a very doable DIY project once you handle moisture first. In this guide, you will test your slab, prepare the surface, choose the right underlayment and lay a floating floor that stays flat for years. Most of the work is in the prep, and the planks themselves click together quickly.

Test and Prepare the Concrete Slab

Concrete releases moisture for months after it is poured, and laminate will swell or cup if that moisture reaches the boards. Before you buy anything, run a moisture test. Tape a 2-foot square of clear plastic sheeting to the slab, seal all four edges, and leave it for 48 to 72 hours. If you see condensation under the plastic or darkening on the concrete, the slab is too wet and you should address the source before installing.

Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).

Next, check flatness. Lay a 6-foot straightedge across the floor in several directions. Dips deeper than about 3/16 inch over 10 feet should be filled with patching compound, and high spots should be ground down. Sweep and vacuum thoroughly, because a single pebble under a plank will show up as a squeak or a crack later.

Choose the Right Underlayment

A foam or cork underlayment with a built-in vapor barrier is the standard choice over concrete. Manufacturers usually specify a 6-mil polyethylene vapor barrier for slab installations, so check that your underlayment includes one or add a separate sheet. Overlap seams by about 8 inches and tape them. Do not use a foam pad with no barrier on a ground-level slab, since it can trap moisture against the concrete.

For more on comparing underlayment and flooring types, see Wooden Flooring vs Laminate: Which Wins for Your Home? (2026) and Laminate Flooring Installation Kits: What to Buy and How to Use Them.

Lay the Laminate as a Floating Floor

Laminate on concrete should float, meaning it is not glued or nailed down. Start in the room’s longest, straightest line, usually parallel to the main window or light source. Leave a 1/4- to 3/8-inch expansion gap along every wall, and use spacers to hold it consistent.

  1. Measure the room and dry-lay the first row to check how the last plank will fit. Trim it so the end row is at least 6 inches wide.
  2. Cut the first plank so the tongue faces the wall, then click the long edge of the next plank in at a 20- to 30-degree angle and lower it flat.
  3. Continue row by row, staggering end joints by at least 6 inches between rows.
  4. Tap the ends together with a tapping block and a rubber mallet, never directly on the locking edge.
  5. Install baseboard or quarter-round trim over the gap. Do not nail through the floor.

Tools and Materials Checklist

  • Plastic sheeting, painter’s tape and a tape measure for the moisture test
  • Straightedge, patching compound and a floor scraper
  • Underlayment with a vapor barrier, plus seam tape
  • Laminate planks, spacers and a jigsaw or circular saw for cuts
  • Tapping block, rubber mallet, pull bar and utility knife

A tapping block protects the locking edges while you seat each joint, which prevents the chipped corners that often ruin a row. A pull bar lets you close the final row against the wall without damaging the tongue. A floor-specific spacer set keeps your expansion gap even around the whole room.

  • Laminate tapping block and pull bar set: protects the edges while you seat planks. View on Amazon
  • Laminate floor spacer set: holds a consistent expansion gap at every wall. View on Amazon
  • Foam underlayment with vapor barrier: a common choice for slab installs. View on Amazon

Common Mistakes to Avoid

  • Skipping the moisture test and laying over a damp slab.
  • Forgetting the expansion gap, which lets the floor buckle as it expands.
  • Aligning end joints in the same line from row to row, which weakens the floor.
  • Tapping on the locking edge instead of using a block.
  • Nailing or gluing the floor down, which defeats the floating design.

FAQ

Can I install laminate directly on concrete without underlayment?

Most manufacturers recommend an underlayment with a vapor barrier over concrete, since it cushions the floor and blocks moisture. Installing without one can void the warranty and makes noise and moisture problems more likely.

How do I know if my concrete is too wet for laminate?

Run the plastic sheet test for 48 to 72 hours. Condensation or dark spots under the sheeting mean the slab is still releasing moisture, so wait or address the source first.

Do I need a professional for this job?

Many homeowners complete a laminate install on concrete themselves, but a flooring professional can help if your slab has serious moisture or leveling problems. Consult a professional before proceeding if you find cracks, water intrusion or significant unevenness.

Conclusion

Successful installation of laminate flooring on concrete depends on testing moisture, leveling the slab and using a proper vapor-barrier underlayment. Once that groundwork is done, the floating layout is straightforward. Take your time on the prep, and the finished floor should stay stable for years.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.