Updated November 2026

Buying laminate flooring at Sam’s Club can save you a trip to several stores, but the right choice depends on your room, your subfloor, and how much you plan to install yourself. This guide walks through measuring, choosing a product, and preparing the floor so your laminate locks together cleanly and stays put. By the end, you will know exactly what to bring home and what to check before you open the box.

Step 1: Measure the Room and Add Overage

Measure the length and width of each room in feet, multiply them to get square footage, and add 10 percent for cuts and waste. Rooms with angles, closets, or a lot of doorways need closer to 12 to 15 percent. Sketch the room on paper and mark where the planks will run, since laminate usually looks best running parallel to the longest wall or the main light source.

Shopping for one? See our guide: What's the Difference Between Vinyl Flooring and Laminate Flooring? (2026).

Step 2: Choose the Right Wear Rating and Finish

Laminate is rated by its abrasion class, and manufacturers generally match these ratings to traffic levels. Lower ratings suit bedrooms and guest rooms, while higher ratings are better for hallways, kitchens, and homes with pets. Check the product label for the wear layer thickness and the AC rating, and compare the surface texture in the store under different lighting. Embossed textures hide dust and minor scratches better than smooth gloss finishes.

Step 3: Prepare the Subfloor and Underlayment

Laminate floats over the subfloor, so the surface underneath matters more than most beginners expect. The subfloor should be flat within about 3/16 inch over a 10-foot span, clean, dry, and free of debris. Use a foam or cork underlayment for sound and comfort, and add a vapor barrier over concrete slabs. Pull up any loose trim and plan to undercut door casings so the planks slide underneath.

Tools and materials checklist

  1. Tape measure and pencil
  2. Laminate flooring planks with 10 to 15 percent extra
  3. Underlayment roll and vapor barrier, if on concrete
  4. Tapping block and pull bar
  5. Spacers for the perimeter gap
  6. Miter saw or jigsaw for cuts
  7. Utility knife and straightedge for underlayment

Step 4: Install the Planks

Start in the corner of the room with the tongue side facing the wall, and leave a gap of about 1/4 inch at every wall using spacers. Angle each new plank into the groove of the previous row, lower it flat, and tap the end joint closed with a tapping block. Stagger the end joints by at least 6 inches between rows, and keep a close eye on alignment every few rows. Cut the last row to fit, then reinstall trim or quarter round to cover the expansion gap.

Common mistakes to avoid

  • Buying too little. Running short mid-room means hunting for a matching batch, which may not exist.
  • Skipping the acclimation period. Let the boxes sit in the room for at least 48 hours before installing.
  • Ignoring the perimeter gap. Without it, the floor can buckle as it expands.
  • Installing over an uneven subfloor. Bumps show through and can cause clicks to separate.
  • Forgetting the transitions. Plan for threshold strips at doorways to other flooring.

A tapping block protects the locking edges while you seat each plank, and a pull bar helps you close the last row against the wall. A foam underlayment roll gives the floor a quiet, cushioned feel and helps smooth minor subfloor variation.

  • Tapping block for laminate: protects the tongue and groove while you seat each plank. View on Amazon
  • Laminate pull bar: closes the final row snugly against the wall. View on Amazon
  • Foam laminate underlayment: adds cushion and sound reduction under floating floors. View on Amazon

FAQ

Can I install laminate flooring from Sam’s Club myself?

Yes, most homeowners with basic tools can install floating laminate with click-lock edges. Consult a professional if your subfloor needs major leveling or repair.

How do I confirm the product is in stock before I go?

Check the official Sam’s Club website or call the store ahead to confirm current availability and sizes. Stock and selections can change without notice.

Do I need underlayment with laminate flooring?

Most laminate products require underlayment for moisture protection, sound reduction, and comfort. Check the manufacturer’s instructions for the specific product you buy.

Conclusion

Measure carefully, pick a wear rating that fits the room, and prepare the subfloor before you start. Take your time with the perimeter gap and staggered joints, and the floor will look clean and last for years. Once the first row locks in, the rest of the job goes much faster.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.