Updated November 2026
Bathroom tub tile installation comes down to four things: a flat, sound substrate, a waterproof layer behind the tile, correctly set tile with full mortar coverage, and joints sealed against water. Get those right and your tub surround will shrug off daily showers for decades. Skip one and you will see cracked grout and soft drywall within a year or two.
Prep the Tub Surround and Substrate
Start by stripping the old wall covering down to the studs or to a solid cement backer board. Check the tub flange and the wall plane with a 4-foot level. Shim high spots and fill low ones so the tile will sit flat. Tile will not hide a bulge, and a wavy wall shows up as uneven courses.
Shopping for one? See our guide: Top 3 Tile Looking Laminate Flooring Picks for Bathrooms and Kitchens.
Next, install cement backer board or a foam-based board rated for wet areas. Screw it every 8 inches along the studs, and leave a 1/8-inch gap above the tub rim so water cannot wick into the board. Seal the seams with alkali-resistant mesh tape and a thin-set or a liquid waterproofing membrane. If you want more background, see Tile Installation on Plywood: A Step-by-Step Guide for DIY Renovators.
Waterproof and Layout the Tile
Apply a waterproofing membrane across the entire tub surround, including the wall above the tub rim and the corners. Two coats are standard, and the membrane should be fully cured before you set tile. Manufacturers specify cure times on the label, so follow them rather than guessing.
Dry-lay the tile on the floor first. Mark a centerline on the back wall and work outward so you do not end with a sliver at the top edge. Aim for cut tiles of at least half width at the corners and along the tub rim. Plan the cut edges to fall behind the faucet or out of sight where possible.
Set, Grout and Seal the Tile
Mix modified thin-set to a peanut-butter consistency. Comb it onto the wall with a notched trowel, using the notch size listed on the tile packaging. Back-butter larger tiles so the mortar makes full contact. Press each tile in with a slight twisting motion, then check with a level. Leave a 1/8-inch gap at the tub rim and fill it later with silicone, not grout.
Wait the thin-set cure time, usually 24 hours, before grouting. Mix grout to the consistency of toothpaste and push it into the joints diagonally with a rubber float. Wipe off excess with a damp sponge in small sections, then let the grout cure before sealing.
Steps at a Glance
- Strip the wall and confirm the substrate is flat within about 1/8 inch over 4 feet.
- Install cement or wet-area backer board with a gap above the tub rim.
- Apply two coats of waterproofing membrane and let it cure.
- Dry-lay the tile and set a centerline.
- Set tile with notched thin-set and check level as you go.
- Grout after the thin-set cures, then clean the haze.
- Caulk the tub-to-tile joint with 100 percent silicone.
Common Mistakes to Avoid
- Setting tile directly on drywall or green board, which fails when water gets behind it.
- Grouting the tub-to-tile joint. Grout cracks under the flex of the tub; silicone holds.
- Skipping the membrane at the corners and above the tub rim.
- Rushing the cure times for thin-set, grout and membrane.
- Using the wrong notch size, leaving voids under large tiles.
Recommended Gear
- Notched trowel set lets you match the notch size to your tile, which helps prevent hollow spots. View on Amazon
- Rubber grout float packs grout into joints evenly and removes excess cleanly. View on Amazon
- Cement backer board gives a stable, moisture-tolerant base for the tile. View on Amazon
FAQ
Can I tile over my existing tub surround?
Sometimes, if the existing surround is solid, flat and fully bonded. Most pros recommend removing it, because hidden water damage often sits behind old tile. For another angle, check out Fiberglass Pool Tile Installation: A Step-by-Step Guide for DIY Renovators.
How long should I wait before grouting?
Follow the thin-set manufacturer’s cure time, which is often 24 hours. Grouting too early can cause the tile to shift.
Should I use grout or silicone at the tub edge?
Use 100 percent silicone at the tub-to-tile joint. The tub flexes, and grout will crack there over time. Worth reading next: Tub Surround Tile Installation: A Step-by-Step Guide for DIY Renovators.
Conclusion
A tub surround that lasts comes from flat substrate, a continuous waterproof layer and properly set tile with silicone at the tub edge. Take the prep and cure times seriously and the job will hold up. For planning the budget and materials, see Tub Surround Tile Installation Cost: A Step-by-Step Guide for Renovators and Large Format Tile Installation: A Step-by-Step Guide for DIY Renovators. If your wall or plumbing looks questionable, consult a licensed professional before you start.

