Updated November 2026

Learning how to get up laminate flooring means working backward through the installation. You will remove the trim, unlock the floating planks one row at a time, and lift them out in a way that keeps most of the boards intact. Expect a medium-sized room to take an afternoon, and plan a little longer if you want to save the planks for reuse.

Prepare the Room and Remove the Trim

Clear the floor of furniture, rugs and any loose items. Then take off the baseboards and quarter-round moldings. Pry them gently with a flat bar and slide a scrap piece of wood behind the bar to protect the wall. Number each piece with painter’s tape so you can reinstall it correctly later.

Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).

Next, check the transition strips at doorways and any stair nosing. Many are held by screws or a locking clip, so you may be able to lift them free without tools. If they are glued down, leave them until the planks are out.

Unlock the Planks Row by Row

Most laminate is a click-lock floating floor. Start at a wall and work along the first row. Use a pry bar or a tapping block to separate the joints, then lift the boards upward and away from the adjacent row.

  1. Begin at the wall where the first row meets the baseboard gap.
  2. Slide a flat bar under the end of a plank at a shallow angle and tap it gently to release the long edge.
  3. Lift the plank straight up, not sideways, so the tongue does not snap.
  4. Continue along the row, then move to the next row and repeat.
  5. Stack planks by row, face up, so you can see which ones need to be reused.

If planks resist, check whether glue was used. Some installers apply glue along the joints, especially in wet areas. A little heat from a hair dryer can soften the bond, but do not overheat the surface.

Lift the Underlayment and Clean the Subfloor

Once the planks are up, peel away the underlayment or vapour barrier. Foam underlayment usually comes up in strips, while plastic vapour barriers may be sealed with tape. Inspect the subfloor for swelling, moisture stains or loose boards, since these problems are easier to fix before the new floor goes down. How to Pull Up Laminate Flooring: A Step-by-Step Guide for Beginners goes further into this.

Sweep and vacuum thoroughly. Leftover grit will show through a new underlayment and can cause small bumps.

Checklist: Tools and Supplies

  • Flat pry bar and scrap wood to protect walls
  • Rubber mallet or tapping block
  • Painter’s tape and a marker for labeling
  • Utility knife for cutting old underlayment
  • Shop vacuum and dust mask
  • Safety glasses and knee pads

Common Mistakes to Avoid

  • Lifting planks sideways, which can break the locking tongue.
  • Skipping the labels on trim, leading to mismatched pieces at reinstall.
  • Pulling too hard on glued joints instead of loosening them first.
  • Ignoring moisture damage on the subfloor until the new floor is down.
  • Working without eye protection when prying trim.

A stiff flat pry bar gives you leverage without denting the planks. View on Amazon

A tapping block protects the edges of the planks while you knock joints apart. View on Amazon

FAQ

Can I reuse laminate planks after removing them?

Often yes, if you lift them carefully and avoid bending the locking edges. Planks with chipped or damaged tongues will not lock again cleanly.

Do I need to remove the baseboards before taking up the floor?

In most cases, yes, because the floor sits under the trim and cannot be lifted otherwise. Removing them also protects the walls from damage.

Is laminate flooring safe to lift if it contains old adhesive?

Glue-down laminate can be harder to remove and may release dust or residue. If you suspect older materials, consult a professional before disturbing the floor.

Conclusion

With the trim off and the planks lifted in labeled rows, the job becomes methodical rather than frustrating. Take your time at the joints and keep the boards you plan to reuse safe. Once the subfloor is clean and dry, you will be ready for whatever comes next.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.