Updated November 2026

Laying Pergo laminate flooring is a manageable weekend project if you prepare the subfloor properly and work in a logical order. By the end of this guide, you will know how to check and level the floor, lay the underlayment, click the planks together, and leave the expansion gap that keeps the floor from buckling later. Pergo laminate is designed as a floating floor, so you will not glue or nail the planks to the subfloor.

Prepare the Room and the Subfloor

Start by moving out furniture and removing baseboards or shoe molding so the planks can slide under them later. Pull up any loose or damaged flooring, then check the subfloor for squeaks, soft spots, and humps. Manufacturers generally specify a flatness tolerance of about 3/16 inch over a 10-foot span, so sand down high spots and fill low ones with a leveling compound before you go further. Confirm the subfloor is dry and clean, since debris under a floating floor creates popping and gaps.

Lay the Underlayment Correctly

Roll out the underlayment perpendicular to the direction you plan to lay the planks, and butt the seams together rather than overlapping them. Many Pergo products include an attached pad, but if yours does not, use a separate foam or cork underlayment rated for laminate. Tape the seams with the tape recommended by the underlayment maker, and trim the edges flush with a utility knife. Check the Pergo installation instructions for your exact product, because some require a vapor barrier over concrete.

Click the Planks Together Row by Row

Begin in the corner of the room that is most visible, with the tongue side of the first board facing the wall. Place plastic or wooden spacers, typically about 5/16 inch, along the walls to create the expansion gap. Join the end of each plank into the previous one at a shallow angle, then lower it flat until the joint clicks. Stagger the end joints by at least 8 inches from row to row so the seams look random and the floor stays stable.

  1. Measure the room width and plan the layout so the last row is at least 2 inches wide.
  2. Cut the first plank to start the staggered pattern, keeping the offcut for the next row.
  3. Click the long edges of each row, then join the short ends.
  4. Use a pull bar and tapping block to close any tight joints, never striking the edge directly.
  5. Cut planks at doorways and around pipes, leaving the expansion gap on every side.
  6. Reinstall baseboards or shoe molding over the gap, not tight against the floor.

Finish the Edges and Transitions

Once the last row is in, fit transition strips at doorways where the laminate meets another floor. Use a matching trim or reducer, and fasten it only to the subfloor, not through the laminate. Give the floor at least 24 hours before heavy foot traffic or replacing furniture, so the joints can settle.

Common Mistakes

  • Skipping the expansion gap, which leads to buckling near walls.
  • Installing planks with end joints lined up in columns, which weakens the floor.
  • Laying over an uneven subfloor and creating hollow spots that squeak.
  • Forcing a joint without checking that the previous row is fully seated.
  • Installing laminate in rooms with standing water or persistent moisture problems.
  • Pull bar and tapping block set: Closes tight joints without damaging the locking edge. View on Amazon
  • Laminate underlayment roll: Provides a moisture barrier and sound reduction under floating planks. View on Amazon
  • Flooring spacer set: Holds the expansion gap consistent along every wall. View on Amazon

For more background on choosing materials and tools, see How to Lay Laminate Flooring: A Step-by-Step Guide for Beginners and 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026). If you want to compare underlayment options before buying, 21 Best Underlayment for Laminate Flooring covers the main types. For cutting planks cleanly around doorways, see How to Cut Laminate Flooring Cleanly: A Step-by-Step Guide.

FAQ

Do I need to glue Pergo laminate flooring?

No. Pergo laminate is a floating floor that locks together at the edges, so it should not be glued or nailed to the subfloor. Check your product instructions to confirm.

How big should the expansion gap be?

Manufacturers typically call for about 5/16 inch around the perimeter of the room. Keep the gap clear of debris and cover it with baseboards or shoe molding.

Can I install Pergo laminate over existing tile?

Sometimes, but it depends on the tile’s flatness and the product’s guidelines. Uneven or cracked tile can cause the floor to rock, so confirm compatibility with the manufacturer before proceeding. A professional can help you assess the floor if you are unsure.

Conclusion

Laying Pergo laminate flooring comes down to a flat subfloor, correct underlayment, a consistent expansion gap, and staggered planks. Work methodically from one corner, check each row as you go, and follow your product’s installation guide for specifics. With careful preparation, the finished floor should stay stable for years.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.