Updated November 2026

Tile installation on concrete is one of the most reliable DIY flooring jobs you can take on, as long as the slab is sound and flat before the first tile goes down. In this guide you will check and prepare the concrete, set up a dry layout, bond the tile with the right mortar, and finish with grout and sealer. Most of the work is in the prep, so that is where we spend the most time.

Step 1: Test and Prepare the Concrete

Start by checking for moisture. Tape a 2-foot square of clear plastic to the slab, seal the edges, and leave it for 48 hours. If moisture collects under the plastic, the slab is too wet to tile directly, and you should talk to a flooring professional about a moisture barrier before going further.

Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).

Next, check flatness. Lay a 6-foot straightedge across the floor in several directions. Tile bonds best where the surface varies no more than about 1/8 inch over 10 feet. Grind high spots with a concrete grinder, and fill low spots and cracks with a patching compound or a self-leveling underlayment made for tile use.

Finally, clean thoroughly. Remove paint, adhesive, sealers and dust. Oil or curing compound will stop mortar from bonding, so degrease the floor if you are unsure what was applied.

Step 2: Plan the Layout

Measure the room and find the center point by snapping chalk lines between opposite midpoints. Dry-lay a row of tiles along each line, leaving grout spacers in place. If the last row at either wall would be less than half a tile wide, shift the layout by half a tile so the cuts are larger and look more even. Mark your lines clearly before you mix anything.

Step 3: Mix Mortar and Set the Tile

Choose a thinset mortar rated for your tile type. Large-format porcelain usually needs a modified thinset rated for large tile, and the notched trowel size should match the tile size and manufacturer instructions. Mix only as much as you can use within the open time printed on the bag.

  1. Spread mortar over a small section with the flat side of the trowel, then comb it with the notched side in one direction.
  2. Press each tile firmly with a slight twisting motion to collapse the ridges.
  3. Check every few tiles with a level and lift one to confirm full coverage. Aim for at least 95 percent contact on floors.
  4. Use a rubber mallet and a beating block to level tiles that sit high.
  5. Let the floor cure for the time the mortar manufacturer specifies, usually 24 hours before grouting and longer before heavy traffic.

Step 4: Grout, Seal, and Finish

Once the tile is set, remove spacers and grout with a rubber float held at an angle, working across the joints. Wipe with a damp sponge after the grout firms, then polish the haze off once it dries. Cement-based grout benefits from a penetrating sealer, which you should apply after the grout cures as directed on the label. Seal natural stone before grouting if the manufacturer recommends it.

Tools and Materials Checklist

  • Concrete grinder and patching compound
  • 6-foot straightedge and chalk line
  • Notched trowel matched to tile size
  • Modified thinset mortar and mixing paddle
  • Tile cutter or wet saw
  • Rubber mallet and beating block
  • Grout float, sponge, and grout sealer
  • Tile spacers: Keep joints consistent across the whole floor, which matters more than most beginners expect. View on Amazon
  • Wet saw: A wet saw gives clean edges on porcelain and makes cuts at walls and around the toilet flange far easier. View on Amazon
  • Rubber grout float: A float with firm rubber packs grout into joints without tearing the surface. View on Amazon

Common Mistakes to Avoid

  • Skipping the moisture test, then finding the tile lifting months later.
  • Mixing more thinset than you can use, which leads to skinning and weak bonds.
  • Ignoring flatness, so tiles rock or crack under load.
  • Grouting too soon, before the mortar has cured.
  • Using the wrong trowel size, leaving voids under the tile.

For more on planning and sequencing, see Flooring and Tile Installation: A Step-by-Step Guide for DIY Renovators and Large Format Tile Installation: A Step-by-Step Guide for DIY Renovators.

FAQ

Can you tile directly over concrete?

Yes, if the slab is dry, flat, clean, and free of cracks or coatings that block adhesion. Test for moisture and fix any high or low spots first.

Do you need an underlayment on concrete?

Usually not, unless the slab is uneven, cracked, or moisture-prone. In those cases a self-leveling compound or a membrane designed for tile is the better choice. A related read: Carpet Tile Installation on Concrete: A Step-by-Step Guide for DIY Renovators.

How long should you wait before walking on new tile?

Light foot traffic is often fine after about 24 hours, but follow the mortar and grout manufacturer’s instructions for full cure times, which can be longer.

Conclusion

Tile installation on concrete rewards careful preparation more than speed. Test the slab, level it, plan your layout, and match your mortar to your tile. Take your time with each stage, and the finished floor should stay solid for years.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.