Updated November 2026

For most drywall repairs, you will want 120-grit sandpaper for the first pass on joint compound and 150 to 220-grit for the final smoothing before primer. Choosing the right grit at each stage keeps you from gouging the paper face, leaving scratch marks, or spending an hour sanding a patch that should have taken ten minutes. This guide walks through which grit to use, when to switch, and how to finish a repair that disappears under paint.

Why Grit Choice Matters for Drywall Repair

Drywall is gypsum core wrapped in thin paper. Coarse sandpaper cuts through the paper face quickly, which exposes the core and leaves a fuzzy, uneven surface. Fine sandpaper works slowly on thick compound and can leave you with bumps and ridges you then have to fill again. The goal is to match the grit to the thickness of the compound and to how smooth the surface needs to be.

Shopping for one? See our guide: 6 Best 3M Drywall Repair Kit Options for Home Repairs (2026).

Choosing the Right Grit at Each Stage

Most drywall repairs move through three stages, and each one calls for a different abrasive.

  • Rough shaping (80 to 120 grit): Use this only to knock down thick, lumpy compound or ridges at the edge of a patch. Work lightly and keep the sander moving.
  • Smoothing between coats (120 to 150 grit): This is the workhorse grit for most repairs. It levels joint compound without tearing the paper face.
  • Final finish (180 to 220 grit): Use this on the last coat before primer or paint. It removes fine scratches and blends the patch into the surrounding wall.

Sanding Sponge or Sandpaper Sheet?

Sanding sponges conform to curved areas and corners, while sheets on a block give you a flatter, more controlled surface on large patches. Many DIYers keep both on hand. Sponges are forgiving because they flex, which makes them less likely to dig into the wall.

Step-by-Step: Sanding a Drywall Patch

  1. Let the compound dry fully. Thick coats can take 24 hours or more, depending on humidity and thickness.
  2. Start with 120-grit on a sanding block to flatten ridges and high spots.
  3. Switch to 150 or 180-grit for the second and third coats, working in light, circular or diagonal strokes.
  4. Feather the edges outward so the patch blends into the surrounding wall.
  5. Finish with 220-grit, then wipe the dust away with a damp cloth or a dry brush.
  6. Inspect the wall at a low angle with a flashlight. Mark any remaining high spots or pinholes with a pencil and repeat.

Dust Control and Wall Inspection

Drywall dust is fine and gets everywhere. Sand with the room ventilated and wear a N95 or better dust mask and eye protection. Wipe down surfaces before priming, because leftover dust will cause primer and paint to bond unevenly. Check the repair under raking light after priming, since primer often shows flaws that were invisible on bare compound.

Tools and Supplies Checklist

  • 120, 150, and 220-grit sandpaper or sanding screens
  • A sanding block or pole sander
  • A sanding sponge for corners and curves
  • A N95 dust mask and safety glasses
  • A damp sponge or microfiber cloth for cleanup
  • A flashlight for checking the surface at an angle

A pole sander makes ceiling and high-wall repairs far less tiring, since you can keep your arms down and your neck relaxed. Look for a model with a swivel head that accepts standard sanding sheets. View on Amazon

A sanding sponge pack in several grits lets you switch quickly between stages without hunting for a fresh sheet. Corner-friendly profiles help on window trim and wall edges. View on Amazon

A respirator rated for dust protects your lungs during long sanding sessions, which matters more than most people expect. Choose one that seals snugly against your face. View on Amazon

Common Mistakes

  • Starting with grit that is too coarse, which tears the paper face and leaves gouges.
  • Sanding wet or partially dry compound, which clogs the paper and smears the surface.
  • Pressing too hard, which creates dips around the patch.
  • Skipping the final 220-grit pass, so the patch shows through paint as a dull spot.
  • Forgetting to remove dust before priming, which causes flashing and uneven sheen.

If you are repairing a larger area or water-damaged drywall, the process changes and a licensed contractor can help you judge whether the substrate is sound. For related steps, see Sheetrock and Drywall Repair: A Step-by-Step Guide for Beginners, and for how to handle the final coat, see Drywall Repair and Painting: A Step-by-Step Guide for Beginners. If you need supplies first, Supplies for Drywall Repair: A Step-by-Step Guide for Beginners covers what to stock.

FAQ

What grit sandpaper should I use on drywall compound?

Use 120-grit for shaping thick compound and 150 to 220-grit for smoothing between coats and the final finish. Avoid anything coarser than 120 on the paper face.

Can I use 80-grit sandpaper on drywall?

Only for knocking down large ridges or dried drips, and with a light touch. It cuts quickly and can tear the paper, so switch to 120-grit or finer as soon as the surface is close to level.

Is 220-grit too fine for drywall?

No. It is the right choice for the final pass before primer, since it removes scratches without damaging the compound. Using it as your first grit, though, would take far too long on thick patches.

Conclusion

Start coarse enough to level the compound, then step down to 150 or 180-grit and finish at 220 before priming. Keep your pressure light, control the dust, and inspect the wall under raking light before painting. With the right grit at each stage, most small repairs will disappear completely.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.