Updated November 2026

Wood laminate flooring Pergo style gives you the look of real hardwood with a click-together floating floor you can install yourself over a weekend. This guide walks through choosing the right product, preparing the subfloor, and laying the planks so the floor stays tight and quiet. The steps are the same ones we followed in our own living room, along with the spots where we slowed down and double-checked.

Choose the Right Pergo Product for Your Room

Pergo sells several collections, and the differences matter more than the wood-look photos suggest. Check the wear rating, the locking system, and whether the planks are rated for moisture. Pergo’s own product pages list these specifications, so compare them before you buy. A higher wear layer suits busy hallways and kitchens, while a lighter-duty plank can work in a bedroom with little foot traffic.

Shopping for one? See our guide: 7 Best Light Wood Laminate Flooring Options for Every Room.

Before you order, measure the room and add about 10 percent for cuts and waste. Look at the plank width and length as well, since wider and longer boards show fewer seams but can be harder to handle alone. We also found Grey Colour Laminate Flooring: How to Choose the Right Shade (Step-by-Step) useful on this point.

Prepare the Subfloor and Room

A floating laminate floor only performs as well as the surface under it. Plan on about 48 hours of acclimation: stack the boxes flat in the room with the heat and humidity at normal living levels. Then check the subfloor.

  1. Clear the room and remove baseboards or shoe molding.
  2. Sweep and vacuum the subfloor thoroughly.
  3. Check for high spots with a straightedge and sand or grind them down.
  4. Fill low spots and dips with a leveling compound, then let it cure fully.
  5. Lay down the underlayment and vapor barrier as the manufacturer specifies.

If your subfloor is concrete, test for moisture before you start. Our guide on Vapor Barrier for Laminate Flooring: A Step-by-Step Guide for Beginners covers when a barrier is needed. If you want more background, see 7 Best Wood Floor Router Bits for Flooring Projects (2026).

Lay the Planks Step by Step

Start in the corner that will be most visible, usually the one closest to the main entry. Leave a gap of roughly 1/4 inch along every wall so the floor can expand. Spacers do the job well and keep the gap even.

  1. Set the first row with the tongue facing the wall, then lock the end joints at an angle and lower them flat.
  2. Stagger end joints by at least 8 inches from row to row so the floor looks random and stays strong.
  3. Cut the last plank in each row with a saw and use the leftover piece to start the next row when it is long enough.
  4. Tap joints together gently with a tapping block, never directly with a hammer on the edge.
  5. Install transition strips at doorways and reinstall baseboards or quarter-round trim to hide the gap.

For a clean finish on stair edges and cut ends, see Stair Nose Laminate Flooring: How to Choose and Install It Right.

Tools and Supplies Checklist

  • Tape measure and pencil
  • Pull bar and tapping block
  • Spacers for the wall gap
  • Circular or miter saw with a fine-tooth blade
  • Straightedge and leveling compound
  • Underlayment and vapor barrier
  • Safety glasses and knee pads

A pull bar lets you snug the last row against the wall without damaging the locking edge. Search for a pull bar set made for laminate installs.

A tapping block protects the plank edge when you close joints. View on Amazon

A quality underlayment with a built-in vapor barrier reduces the number of separate products you need to buy and place. View on Amazon

Common Mistakes to Avoid

  • Skipping acclimation, which can cause gaps or buckling later.
  • Forgetting the expansion gap at walls and under trim.
  • Letting end joints line up in neighboring rows.
  • Installing over an uneven subfloor and expecting the planks to hide the dips.
  • Using too much force when locking planks, which can chip the edges.

FAQ

Can I install Pergo wood laminate flooring over existing tile?

Often yes, if the tile is flat, well bonded and level, but the manufacturer’s instructions and your local building guidance should confirm it first. Any loose or cracked tile should be repaired before you start.

How long does a Pergo laminate floor last?

Lifespan depends on the wear rating, foot traffic and how well the floor is maintained. Pergo product pages list recommended use levels for each collection.

Do I need professional help to install it?

Many homeowners install floating laminate themselves, but if your subfloor needs major repair or the layout is complicated, consult a flooring professional.

Conclusion

Choosing the right Pergo collection, preparing a flat and dry subfloor, and leaving proper expansion gaps will get you most of the way to a floor that looks good and lasts. Take your time with the first row, since it sets the pattern for everything after it. With careful measuring and patience, a wood laminate floor is a very achievable weekend project.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our DIY home renovation guides, checking product details against manufacturer specifications and owner feedback.