Updated November 2026
A laminate flooring vapour barrier is a thin plastic or foil sheet that stops moisture rising from the subfloor into the planks above. Installed correctly, it protects the joints from swelling and keeps your floor from cupping, especially over concrete. This guide covers when you need one, how to choose it, and how to lay it without creating new problems.
Do You Need a Vapour Barrier for Your Subfloor?
The answer depends on what the planks are sitting on. Concrete slabs, including those on grade and in basements, release moisture for months after pouring, so a barrier is almost always needed there. Plywood or OSB subfloors over a crawl space or a ground-level room usually benefit from one too. Over a dry, sealed wood subfloor on an upper floor, a barrier is often optional, though many manufacturers still call for one.
Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).
Check your product’s installation instructions first. Many laminate warranties require a moisture barrier on concrete, and skipping it can void coverage. If you are unsure whether your slab is dry enough, a simple plastic-sheet test or a moisture meter reading can help. Consult a flooring professional or structural engineer if you suspect serious water intrusion.
Choosing the Right Barrier Material
Most products fall into two types. Polyethylene sheeting is the usual choice, typically 6-mil or thicker, and it is inexpensive and easy to cut. Foil-faced or foam-backed combination underlayments add a moisture barrier to cushioning and sound reduction, which saves a separate step. Choose a combined product if you also need sound control; otherwise a plain film works well.
Look for a product marked as rated for laminate, and check whether the seams can be taped. A barrier that does not overlap cleanly will not do its job.
How to Install the Vapour Barrier Step by Step
- Clean the subfloor thoroughly and remove any debris, nails or ridges that could puncture the film.
- Roll out the barrier with the plastic side facing up and the seams running perpendicular to the direction you will lay the planks.
- Overlap each seam by at least 8 inches, and tape every seam with a moisture-resistant tape.
- Carry the barrier up the walls about 2 inches, leaving room for the expansion gap, and trim the excess once the room is covered.
- Do not stretch the film tight; leave it slightly loose so it lies flat without wrinkles or bubbles.
- Lay your underlayment, if required, directly over the vapour barrier, then begin the laminate installation.
Leaving the Expansion Gap
The barrier should never bridge the expansion gap at the walls. Trim it so it sits under the baseboard or quarter-round, and keep the gap your laminate manufacturer specifies, usually around 1/4 to 3/8 inch. For a fuller walkthrough of the planks themselves, see How to Install Laminate Flooring: A Step-by-Step Guide for Beginners.
Common Mistakes to Avoid
- Overlapping seams too little, which lets moisture track through the gap.
- Using no tape, so seams open up as the floor settles.
- Installing the barrier upside down, with the film facing the subfloor.
- Pulling the barrier tight against the walls and ruining the expansion gap.
- Skipping the underlayment when the manufacturer requires it, or stacking two underlayments that conflict.
Recommended gear
A roll of 6-mil polyethylene sheeting gives you a basic barrier that works on most slabs and is easy to cut to size. A flooring underlayment with a built-in vapour film is a good option when you also want sound reduction, and manufacturers often list both functions on the packaging. A moisture-resistant seam tape is essential for sealing the overlaps so the barrier stays continuous.
- Polyethylene vapour barrier sheeting: a budget-friendly film that covers large areas quickly. View on Amazon
- Laminate underlayment with vapour film: combines moisture protection and cushioning in one layer. View on Amazon
- Moisture-resistant seam tape: seals overlaps so the barrier stays continuous. View on Amazon
If you are still choosing underlayment, 21 Best Underlayment for Laminate Flooring compares options, and Subfloor Preparation and Flooring Underlayment Explained covers what the subfloor needs before any of it goes down.
FAQ
Do I always need a vapour barrier under laminate flooring?
Not always, but you almost always need one over concrete. Over a dry, sealed wood subfloor on an upper floor it is often optional, so check your manufacturer’s requirements.
Can I use plastic sheeting as a vapour barrier?
Yes, a 6-mil polyethylene sheet is a common choice. Make sure it is rated for flooring use, overlap the seams, and tape them.
Should the vapour barrier go over or under the underlayment?
Place the vapour barrier directly on the subfloor, with the underlayment on top of it, unless your product instructions say otherwise.
Conclusion
A properly installed vapour barrier protects your laminate from moisture rising out of the subfloor, and it is especially important over concrete. Overlap and tape every seam, keep the film clear of the expansion gap, and follow your manufacturer’s instructions. Taking those steps now prevents swelling and warping later.

