Updated November 2026
Quarter round on laminate flooring covers the gap between the floor and the baseboard, hiding the expansion space every floating floor needs. Done right, it looks clean and stays put while the laminate keeps moving with the seasons. This guide walks through choosing the right molding, measuring and cutting the corners, and fastening it without locking the floor in place.
Why Quarter Round Matters on a Floating Floor
Laminate planks click together and float over the subfloor, usually on a thin underlayment. The planks expand and contract with humidity and temperature, so the installer leaves a gap of about 1/4 inch to 3/8 inch around the perimeter. Baseboards are the wrong place to hide that gap, because they are attached to the wall and do not move with the floor.
Shopping for one? See our guide: 7 Best Laminate Flooring Installation Tools for DIY Renovators (2026).
Quarter round sits on the floor, not the wall. It covers the expansion gap while the baseboard stays where it is. The key rule is that the quarter round must be fastened only to the baseboard or wall, never to the laminate itself. Nailing through the floor pins the planks and can cause buckling, cracked seams or gaps that open up later.
Materials and Tools You Will Need
Most of the work requires basic carpentry tools. Gather these before you start so you are not stopping mid-room.
- Quarter round molding, primed or prefinished, in a profile that matches your baseboards
- Miter saw or miter box with a fine-tooth saw
- Tape measure and pencil
- Coping saw for inside corners
- Brad nailer or 18-gauge finish nailer, or a hammer and 1-1/4 inch finish nails
- Wood filler and a putty knife
- Caulk gun and paintable acrylic latex caulk
- Sandpaper, 120 grit
- Touch-up paint that matches the molding
Check that your quarter round is sized for the gap. Standard quarter round is about 3/4 inch on each face. It covers a gap of up to roughly 1/2 inch, which is enough for most laminate installations. If your expansion gap is larger, use a larger shoe molding or install a transition piece instead.
Step 1: Measure the Room Perimeter
Measure each wall from corner to corner, then add the lengths. Measure every wall separately because rooms are rarely perfectly square. Write each length on a piece of painter’s tape stuck to the wall, along with a note about which corners are inside or outside corners. This keeps you from mixing up pieces later.
Buy about 10 percent extra molding to allow for mistakes, especially on the first few cuts.
Step 2: Cut Straight Runs and Outside Corners
Quarter round is cut with 45-degree miters at outside corners and at most inside corners. Set your miter saw to 45 degrees with the molding lying flat on the table, with the bottom edge (the flat side that rests on the floor) against the fence.
- Set the miter saw to 45 degrees, left or right depending on the corner direction.
- Cut the first end of the piece at the angle.
- Hold the piece against the wall and mark the length of the run.
- Cut the opposite end at a 45-degree angle in the matching direction.
- Dry-fit the piece before nailing anything.
For outside corners, the two miters should point the same way so the pieces form a V when joined. Test-fit every corner before you nail, because small adjustments are much easier at this stage.
Step 3: Cope Inside Corners
Most experienced installers cope inside corners rather than mitering them. Coping means cutting one piece square at the end, then shaping the end of the second piece to match the profile of the first. The result hides gaps better than a miter, especially when walls are slightly out of square, which is common in older homes.
How to Cope a Joint
- Cut the first piece square at the end (90 degrees) and install it.
- Cut the second piece at a 45-degree miter. This creates an outline of the profile.
- Follow the outline with a coping saw, angling the blade slightly backward so the cut undercuts the face.
- Test-fit the coped end against the first piece. Remove material in small passes until the profile sits tight.
Pro tip: if you are working in a room with very uneven walls, a slightly loose coped joint is better than forcing a tight fit that splits the molding.
Step 4: Fasten the Quarter Round Correctly
This is where most laminate installations go wrong. The quarter round must be nailed into the baseboard or wall studs only. Use a brad nailer or finish nails about 1-1/2 inches long, driven at a slight angle into the baseboard, not the floor. Space nails every 12 to 16 inches.
Keep the molding bottom about 1/16 inch off the laminate surface when you fasten it. This small clearance lets the floor move without pushing up on the molding. Some installers use a thin spacer or a scrap of cardboard to hold the molding up while nailing.
Check the Gap Before You Finish
Run your hand along the floor edge. The quarter round should sit flush against the baseboard and float just above the planks. If you see the molding pressing into the laminate, back the nail out and reposition the piece.
Step 5: Fill, Caulk and Finish
Fill small nail holes with wood filler, let it dry, then sand smooth. Caulk any gaps between the quarter round and the wall with paintable acrylic latex caulk. Do not caulk between the quarter round and the laminate floor, because that restricts movement and can cause cracking.
Paint or touch up the molding after the caulk dries. Prefinished molding just needs a touch-up pen or paint in the matching color.
Common Mistakes
- Nailing through the laminate. This pins the floor and is the most common cause of buckling.
- Caulking to the floor. A bead of caulk along the laminate edge stops expansion and cracks the caulk within months.
- Skipping the test fit. Cutting all pieces before dry-fitting leads to wasted molding.
- Using the wrong profile. A quarter round that does not match the baseboard looks unfinished, even when the cuts are perfect.
- Forcing a tight fit. Walls are rarely perfectly straight, so a little space is normal and better than a split molding.
Tips for a Clean Result
- Install quarter round after the flooring is fully acclimated and the last row is down, not before.
- Use a stud finder or nail into the baseboard rather than drywall alone to hold the molding securely.
- Keep a scrap of the same molding to test your nail depth and miter angles before working on the real piece.
- Work in one room at a time so pieces do not get mixed up across the house.
- Check the laminate manufacturer’s installation guide for the required expansion gap, since it varies between brands.
Recommended gear
A few tools make this job much easier and more accurate.
- DeWalt DWS716 compound miter saw: A compound miter saw holds consistent 45-degree cuts, which matter for clean outside corners. View on Amazon
- Irwin Strait-Line coping saw: Its fine blade and narrow frame make it easier to follow the coped profile on inside corners. View on Amazon
- DeWalt 18-gauge brad nailer: A brad nailer drives small, nearly invisible fasteners that are less likely to split thin molding. View on Amazon
- DAP Dynaflex 230 acrylic latex caulk: A paintable caulk that stays flexible for filling gaps between the molding and the wall. View on Amazon
FAQ
Should quarter round be nailed into laminate flooring?
No. Quarter round should be fastened only to the baseboard or wall. Nailing into the laminate restricts movement and can cause the planks to buckle or separate.
How much gap should I leave under quarter round on laminate?
Leave the molding about 1/16 inch above the floor surface. The perimeter expansion gap underneath is set during installation, typically around 1/4 inch to 3/8 inch, and the molding simply covers it.
Can I caulk quarter round to laminate flooring?
Avoid caulking between the molding and the floor. Caulk belongs between the molding and the wall, where it can flex without restricting the floor.
Is it better to miter or cope inside corners?
Coping is usually better for inside corners, especially in older homes where walls are not square. Mitered inside corners tend to open up as the wood moves.
What size quarter round do I need for laminate?
Standard 3/4-inch quarter round works for most installations. Check the expansion gap your laminate requires, and use a larger shoe molding if the gap is wider than the molding can cover.
Can I install quarter round myself?
Yes, if you have basic saw and nailing skills. Consult a professional carpenter if your room has unusual angles or if you are unsure about the expansion gap for your specific flooring.
Do I need quarter round if I have baseboards?
Yes, in most floating laminate installations. Baseboards are fixed to the wall and cannot cover the floor expansion gap, so quarter round or shoe molding is needed to hide it.
Should quarter round match the baseboard color?
Most people paint or stain quarter round to match the baseboard, which creates a seamless look. Prefinished molding in a matching color is also a convenient option.
Conclusion
Quarter round on laminate flooring hides the expansion gap while letting the floor move freely. Measure carefully, cope the inside corners, and fasten the molding only to the baseboard. Keep the floor free of nails and caulk, and your installation will look clean for years.
Related reading
- Wooden and Laminate Flooring (2026): Which Is Better for Your Home?
- Wooden Laminate Flooring Identification: How to Tell What You Have
- Wooden Flooring vs Laminate: Which Wins for Your Home? (2026)
- Wood Laminate Flooring Pergo: How to Choose and Lay It Right (Step-by-Step)
- Wood Glue Laminate Flooring: Does It Work? A Step-by-Step Guide
- Wood Floor Laminate Flooring (2026): Which Should You Choose?

